TB 9-2320-279-13&P
0040
2. Raise left wheelwell assembly (7) and position rear edge between bottom of pump
module (2) and mudflap bracket (3). Refer to figure 7.
3. Secure rear edge of left wheelwell assembly (7) and mudflap bracket (3) with three
4397000-068 capscrews (1), existing large washers (20), 4397005-015 washers (19), and
4397064-005 locknuts (18). Do not tighten locknuts (18) at this time. Refer to figure 7.
4. Install remaining two 4397000-382 capscrews (10), 4397004-009 lockwashers (9),
4397005-017 washers (22), and 4397064-007 locknuts (21) to secure left wheelwell
assembly (7) to left front panel assembly (8). Tighten three locknuts (21) to 60 lb-ft and
three locknuts (18) to 37 lb-ft. Refer to figure 7.
5. Install 6433264-01M1 or 6433264-200M1 inner wheel house panel (6) and secure to left
wheelwell assembly (7) with three 4397000-380 capscrews (4) and 4397004-009
lockwashers (5) as shown in figure 7. Tighten capscrews (4) to 60 lb-ft.
6. Install 6433112-01M1 or 6433112-200M1 right wheelwell assembly (11) and secure to
right front panel assembly (13) with one 4397000-382 capscrew (15), 4397004-009
lockwasher (16), 4397005-017 washer (24), and 4397064-007 locknut (23) installed in
center mounting hole as shown in figure 7. Do not tighten locknut (23) at this time.
7. Raise right wheelwell assembly (11) and position rear edge between bottom of pump
module (2) and mudflap bracket (3). Refer to figure 7.
8. Secure rear edge of right wheelwell assembly 11) and mudflap bracket (3) with three
4397000-068 capscrews (1), existing large washers (20), 4397005-015 washers (19), and
4397064-005 locknuts (18). Do not tighten locknuts (18) at this time. Refer to figure 7.
9. Install remaining two 4397000-382 capscrews (15), 4397004-009 lockwashers (16),
4397005-017 washers (24), and 4397064-007 locknuts (23) to secure right wheelwell
assembly (11) to right front panel assembly (13). Tighten three locknuts (23) to 60 lb-ft
and three locknuts (18) to 37 lb-ft. Refer to figure 7.
10. Install 6433264-01M1 or 6433264-200M1 inner wheel house panel (12) and secure to
right wheelwell assembly (11) with three 4397000-380 capscrews (17) and 4397004-009
lockwashers (14) as shown in figure 7. Tighten capscrews (17) to 60 lb-ft.
H. Install 6433309-01M1 or 6433309-200M1 left side access panel assembly (3) and secure
with three 4397000-060 capscrews (9) and 4397004-008 lockwashers (8) as shown in figure
8. Tighten capscrews (9) to 37 lb-ft.
I. Install 6433308-01M1 or 6433308-200M1 right side access panel assembly (22) and secure
with three 4397000-060 capscrews (20) and 4397004-008 lockwashers (21) as shown in
figure 8. Tighten capscrews (20) to 37 lb-ft.
0040-9
